J. F. Agassant, F. Pigeonneau, L. Sardo, and M. Vincent, Flow analysis of the polymer spreading during extrusion additive manufacturing, Addit. Manuf, vol.29, p.100794, 2019.
URL : https://hal.archives-ouvertes.fr/hal-02266943

A. Bejan, Porous media, Heat transfer handbook, vol.15, pp.1131-1180, 2003.

C. Bellehumeur, L. Li, Q. Sun, and P. Gu, Modeling of bond formation between polymer filaments in the fused deposition modeling process, J. Manuf. Processes, vol.6, issue.2, pp.70071-70078, 2004.

H. Bikas, P. Stavropoulos, and G. Chryssolouris, Additive manufacturing methods and modelling approaches: a critical review, Int. J. Adv. Manuf. Technol, vol.83, issue.1-4, pp.389-405, 2015.

R. Comminal, M. P. Serdeczny, D. B. Pedersen, and J. Spangenberg, Numerical modeling of the strand deposition flow in extrusion-based additive manufacturing, Addit. Manuf, vol.20, pp.68-76, 2018.

S. F. Costa, F. M. Duarte, and J. Covas, Thermal conditions affecting heat transfer in FDM/FFE: a contribution towards the numerical modelling of the process, Virtual Phys. Prototy, vol.10, issue.1, pp.35-46, 2015.

S. F. Costa, F. M. Duarte, and J. A. Covas, Estimation of filament temperature and adhesion development in fused deposition techniques, J. Mater. Process. Technol, vol.245, pp.167-179, 2017.

G. D. Goh, Y. L. Yap, H. K. Tan, S. L. Sing, G. L. Goh et al., Process-structure-properties in polymer additive manufacturing via material extrusion: A review, Crit. Rev. Solid State Mater. Sci, vol.45, issue.2, pp.113-133, 2020.

M. Hebda, C. Mcilroy, B. Whiteside, F. Caton-rose, and P. Coates, A method for predicting geometric characteristics of polymer deposition during fused-filament-fabrication, Addit. Manuf, vol.27, pp.99-108, 2019.

Y. Jaluria, Heat transfer handbook, pp.525-571, 2003.

Y. S. Ko, D. Herrmann, O. Tolar, W. J. Elspass, and C. Brändli, Improving the filament weld-strength of fused filament fabrication products through improved interdiffusion, Addit. Manuf, vol.29, p.100815, 2019.

M. E. Mackay, Z. R. Swain, C. R. Banbury, D. D. Phan, and D. A. Edwards, The performance of the hot end in a plasticating 3D printer, J. Rheol, vol.61, issue.2, pp.229-236, 2017.

C. Mcilroy and R. S. Graham, Modelling flow-enhanced crystallisation during fused filament fabrication of semi-crystalline polymer melts, Addit. Manuf, vol.24, pp.323-340, 2018.

C. Mcilroy and P. Olmsted, Disentanglement effects on welding behaviour of polymer melts during the fused-filament-fabrication method for additive manufacturing, Polymer, vol.123, pp.376-391, 2017.

F. Peng, B. D. Vogt, and M. Cakmak, Complex flow and temperature history during melt extrusion in material extrusion additive manufacturing, Addit. Manuf, vol.22, pp.197-206, 2018.

F. Pigeonneau, D. Xu, M. Vincent, and J. F. Agassant, Heating and flow computations of an amorphous polymer in the liquefier of a material extrusion 3d printer, Addit. Manuf, vol.32, p.101001, 2020.
URL : https://hal.archives-ouvertes.fr/hal-02425219

J. E. Seppala and K. D. Migler, Infrared thermography of welding zones produced by polymer extrusion additive manufacturing, Addit. Manuf, vol.12, pp.71-76, 2016.

M. P. Serdeczny, R. Comminal, D. B. Pedersen, and J. Spangenberg, Experimental validation of a numerical model for the strand shape in material extrusion additive manufacturing, Addit. Manuf, vol.24, pp.145-153, 2018.

R. K. Shah and A. L. London, Laminar flow forced convection in ducts. A Source book for compact heat exchanger analytical data, 1978.

Q. Sun, G. M. Rizvi, C. T. Bellehumeur, and P. Gu, Effect of processing conditions on the bonding quality of FDM polymer filaments, Rapid Prototyping J, vol.14, issue.2, pp.72-80, 2008.

J. P. Thomas and J. F. Rodríguez, Modeling the fracture strength between fused-deposition extruded roads 16, pp.16-23, 2000.

B. N. Turner, R. Strong, and S. A. Gold, A review of melt extrusion additive manufacturing processes: I. Process design and modeling, Rapid Prototyping J, vol.20, issue.3, pp.192-204, 2014.

F. Yang and R. Pitchumani, Healing of thermoplastic polymers at an interface under nonisothermal conditions, Macromolecules, vol.35, issue.8, pp.3213-3224, 2002.

Y. Zhang, G. Guillemot, M. Bernacki, and M. Bellet, Macroscopic thermal finite element modeling of additive metal manufacturing by selective laser melting process, Comput. Methods Appl. Mech. Eng, vol.331, pp.514-535, 2018.

Y. Zhang and V. Shapiro, Linear-time thermal simulation of As-Manufactured FDM components, 2017.